Hello, I am an electrical engineer having an extensive experience as a professor in higher education in engineering science and electrical engineering, as well as great experience as an embedded systems engineer, in EE architecture, ADAS, Testing and validations in the automotive sector. In this course, I offer training in engineering fields related to automotive engineering, system engineering, testing and validation, embedded systems, and ADAS systems. My methodology is based on the acquisition of theoretical concepts in a simple manner, as well as the practical aspects of current market techniques. I also offer CV correction/preparation sessions, preparation for job interviews mainly in the automotive sector.

Hello, I am an electrical engineer having an extensive experience as a professor in higher education in engineering science and electrical engineering, as well as great experience as an embedded systems engineer, in EE architecture, ADAS, Testing and validations in the automotive sector. I offer support courses and training in engineering science subjects, particularly in Automation and Industrial Control, to graduate students. My methodology is based on the acquisition of knowledge and course concepts in a very simple manner and also on practical experience using the most widely used software on the market. Automation is the discipline that, generally speaking, deals with the control of systems. It is therefore very important in the industrial field, to which it provides solutions, study methods, and systematic analysis approaches. It is a scientific discipline that studies dynamic systems, signals, and information for the purposes of control or decision-making. This course consists of six chapters, divided as follows: Chapter 1: Introduction to Automation & Controlled Systems Chapter 2: Mathematical Modeling of Controlled Systems Chapter 3: Time & Frequency Analysis of Controlled Systems Chapter 4: Controlling Systems & Block Diagram Algebra Chapter 5: Stability & Performance of Controlled Systems Chapter 6: Correction and Regulation of Controlled Systems

Hello, I am an engineer and doctor in electrical engineering and professor of higher education in engineering sciences, experienced in the field of electrical engineering, I offer for graduate students support courses and training in the subjects engineering sciences, in particular in electrical circuits and electricity. My methodology is based on the acquisition of knowledge and course concepts in a very simple way and also on practice using the most widely used software on the market. The "electrical circuits" course is an essential element of the "engineering sciences" module, or industrial engineering sciences, which brings together scientific disciplines related to the engineering profession, particularly in the field of electrical engineering. . It deals with the basics of electricity: from the notion of a circuit, to the various existing electrical components, to the resolution of problems and exercises using general theorems. At the end of this course, the student must be able to: Analyze in continuous mode and in sinusoidal mode the electrical circuits based on passive components; Use the theoretical knowledge necessary for solving electrical problems; Use the theoretical knowledge necessary for the proper conduct of practical work; Carry out and analyze electrical circuits on design and simulation software used by engineers; I also give courses and training in: Embedded systems, ADAS systems and automotive engineering Electrical and electronic circuits Automatic Industrial regulation Signal processing C Programming, Assembler, PIC, Arduino Matlab LabVIEW PIC microcontroller Microprocessor

Hello, I am an electrical and electronic engineer with extensive experience as a professor in higher education in engineering sciences and electrical engineering, as well as a rich experience as an embedded systems engineer, in EE architecture, ADAS, Testing and validation in the automotive sector. I offer support courses and training in engineering science subjects for graduate students, particularly in Matlab Simulink programming. My methodology is based on the acquisition of knowledge and course concepts in a very simple way and also on practice using the most widely used software on the market. Matlab is both software and a scientific programming language developed by the American company MathWorks which allows various numerical calculation operations to be carried out. For example, manipulating algorithms, displaying data curves or even generating matrices. It is used in everything that is programming, signals and systems, signal processing... It contains another part of graphical programming called Simulink, dedicated to the programming and modeling of dynamic systems (Widely used in the discipline of automatic and industrial regulation). I also give courses and training in: Embedded systems, ADAS systems and automotive engineering Electrical and electronic circuits Automatic Industrial regulation Signal processing C Programming, Assembler, PIC, Arduino LabVIEW PIC microcontroller Microprocessor

Hello, I am an electrical and electronic engineer with extensive experience as a professor in higher education in engineering sciences and electrical engineering, as well as a rich experience as an embedded systems engineer, in EE architecture, ADAS, Testing and validation in the automotive sector. I propose for the students of the higher cycle a supervision and an accompaniment until the realization of their projects or mini projects in electronics, signal processing, regulation and enslavement... using languages and software such as: Matlab / Simulink, Python, LabVIEW, ISIS Proteus, Arduino... I also give courses and training in: Embedded systems, ADAS systems and automotive engineering Electrical and electronic circuits Automatic Industrial regulation Signal processing C Programming, Assembler, PIC, Arduino PIC microcontroller Microprocessor